If the request was a GET, the record (or as much of it as possible) was moved to the user's work area. You attempted to open an ACB for a SHR(4) KSDS using MACRF=(KEY,CNV) or MACRF = (ADR). X'B4' 180 Return Code=08 Action=OPEN An error occurred in opening a catalog or CRA. X'98' 152 Return Code=08 Action=OPEN Security verification failed: the password specified in the ACB or supplied by the operator for a specific level of access does not match the password in weblink
Sequential files only. Reset specification can result from MACRF = RST in your ACB, open disposition of NEW, or close disposition of DELETE in your DLBL statement. When this is detected during a LOCATE call you may see the following external symptoms: IEC070I 037(050,004,IGG0CLFH)-220,jobname,COPY,dd,0F4D,volser, IEC070I example.cluster,example.cluster.data, IEC070I usercat.name IEC161I 229(050,004,IGG0CLFH)-233 When the call to catalog is for UPDATE, Updating is not permitted. http://www.ibm.com/support/knowledgecenter/SSLTBW_2.1.0/com.ibm.zos.v2r1.ieam600/bb3009i.htm
PROGRAMMER ACTION: Recompile the progam with a larger work area specified. Eliminate duplicate records by processing the data using keyed access with update. A copy of the file was exported with the INHBITSOURCE options and imported into this system.
If you cannot separate the job into smaller jogs, SYSGEN a new supervisor with more programmer logic units (IOTAB xxPRG SYSGEN macro). X'9C' 156 Return Code=08 Action=Request One or more records in this CI may contain duplicate data after an addressed GET-with-update. Equal to zero. Igd17103i Return Code=00 Action=Request VSAM detected an end-of-volume condition.
X'CC' 204 Return Code=08 Action=Request The program issued a PUT to insert a record while in backward mode. Vsam Catalog Return Code Is 48 - Reason Code Is Igg0clfo-28 If the rerun fails, contact your IBM Support Center. This is not new with release 1.4. If you suspect the problem is one of those listed above, perform the corresponding action: Specify SIZE = AUTO on the EXEC statement to increase the size GETVIS area.
Valid HTML 4.01 Transitional Valid CSS 2 Content last modifed: Monday May-26-2009 Website designed by JaTomes Software and Consulting Web site - hosted BlueHost.com - last modified on Tuesday April 26, Idc3007i Error description An IDC3009I 50-4 is issued out of IGG0CLFH when it is detected that bad data is in a VVR buffer and a Secondary volume Q record is expected. PROGRAMMER ACTION: Ensure that in the SYNAD exit routine your program issues a DUMP macro. CONDITION CODE IS 12 IDC0002I IDCAMS PROCESSING COMPLETE.
PROGRAMMER ACTION: Probable job control error. Save the dump you obtain and SYSLOG output for later problem determination. Vsam Catalog Return Code Is 8 - Reason Code Is Igg0cleg-42 One of the following situations may have occurred. Vsam Catalog Return Code Is 68 The error may be caused by such conditions as VSAM finding an unformatted record when expecting a formatted record, a volume containing data other than that expected, or an I/O error.
Correct the conflict and rerun the job. have a peek at these guys It is being reset by another ACB. Attempting to REWRITE a record to a file and the record is not the same size as the record being replaced. 46 READ Sequentially accessed files only. PROGRAMMER ACTION: Changes the device address in the ASSGN statement to that of the VSAM volume being opened. Idcams Return Codes
Non-CI format files are supported only by SAM access (DTF). X'60' 096 Return Code=04 Action=OPEN The file to be opened for input was found to be unusable because catalog recovery for this file failed. Later I found out that the Volume this guy shows in 3.4 through does not have a VVDS on it. check over here APAR status Closed as program error.
I used DEFINE CLUSTER RECATALOG parameter but it failed, //RECAT JOB (654),'VENKAT',CLASS=A, // MSGCLASS=A,NOTIFY=&SYSUID //S1 EXEC PGM=IDCAMS //SYSPRINT DD SYSOUT=* //SYSIN DD * DEFINE CLUSTER - ( - NAME(EMTE.FILE) - VOLUME(WORK05) Iec331i PROGRAMMER ACTION: Verify that your program is using the correct cluster, alternate index, or path name. Correct any errors and rerun the job.
The I/O statement failed because of a boundary violation. PROGRAMMER ACTION: If data integrity problem arise, revert to a valid backup copy of the file. Use Access Method Services EXPORTRA command to export the file for subsequent reimportation. Idc3014i Only one processor may do output to SHAREOPTIONS(4) file at a time.
To assist in problem diagnosis, you might wish to run a SNAP dump 0001, as described in the "Diagnosis Aids" section of VSE/VSAM/VSAM logic, Volume 1 or Volume 2. X'F8' 248 Return Code=08 Action=OPEN IKQLAB or IKQSMVRJ (VSE/VSAM Space Management for SAM Feature) passed an invalid parameter list to the LABEL or EXTRACT marco. Note: For DTFPH, BLKSIZE is taken to be the DTFPH CISIZE minus 7. this content Change your program to avoid task contention for the ACB.
X'BC' 188 Return Code=>0 Action=CLOSE The ACB to be close is currently being used; (for example, by a SHOWCB or TESTCB macro). A SAM ESDS is being loaded or extended by another SAM access user (DTF). X'72' 114 Return Code=00 Action=OPEN The Catalog Check Service Aid was invoked during OPEN processing and detected a catalog irregularity, or there was insufficient storage for Catalog Check processing. Run the Catalog Check Service Aid against the entire catalog; it will identify catalog errors for you.
The device on which the volume is mounted "down" (Job Control command DVCDN). Return Code=08 Action=Request An attempt was made to retrieve a spanned record of a keyed-sequenced file with addressed access. X'C8' 200 Return Code=08 Action=Request An addressed or control-interval access is attempted via a path. This is an invalid prefix.
This does not apply to VSAM sequential files. 06 WRITE Attempted to write to a file that has been opened for INPUT. 07 CLOSE OPEN If the problem persists print the dump from the SYSDMP. (Refer to VSE/VSAM Access Method Services Logic for ivterpretation of the IDUMP output.) Contact your IBM Support Center and make IDUMP You will see the same results on earlier releases. PROGRAMMER ACTION: Either correct the situation that caused the catalog recovery operation for this file to fail, or recreate the file.
© Copyright 2017 silkiconfinder.com. All rights reserved.